Jeep Wrangler Fuse Box Location – wranglerguide.com (2024)

As a Jeep Wrangler owner for over a decade, I’ve had my fair share of electrical issues that required accessing the vehicle’s fusebox. Whether you need to replace a blown fuse or install a new accessory, knowing the location of your Wrangler’s fusebox is essential. In this guide, I’ll walk you through where to find the fusebox in various Jeep Wrangler models and provide some tips for working with fuses.

Fusebox Location in Jeep Wrangler JL and JLU (2018-Present)

In the current generation Jeep Wrangler (JL and JLU models), there is only one fusebox, and it’s located in the engine bay on the passenger side. Here’s how to access it:

1. Open the hood and locate the fusebox on the passenger side of the engine compartment.
2. Press the release tabs on either side of the fusebox cover and lift it off.
3. The fuse diagram is printed on the underside of the cover, which shows the location and amperage of each fuse.

It’s important to note that there is no interior fusebox in the JL and JLU models. If you’re installing an accessory that requires tapping into a fuse, you’ll need to run the power wire through a grommet in the firewall to access the fusebox in the engine bay.

Tips for Installing Accessories on a Jeep Wrangler JL/JLU

If you have the OEM auxiliary switch panel in your Wrangler, you can use the provided wires to power your accessories without tapping into the fusebox. The auxiliary switch panel includes:

• Individual wires for each switch
• An ignition-only wire
• A direct-to-battery wire

These wires are usually located under the passenger footwell, tucked behind the carpet. Utilizing these pre-installed wires can save you time and effort when installing accessories.

Fusebox Location in Jeep Wrangler JK (2007-2018)

The Jeep Wrangler JK has two fuseboxes – one under the hood and one in the interior. Here’s where to find them:

Under Hood Fusebox

1. Open the hood and look for the Power Distribution Center (PDC) on the passenger side of the engine compartment.
2. Remove the cover by pressing the release tabs on either side and lifting it off.
3. The fuse diagram is printed on the underside of the cover.

Interior Fusebox

1. Look under the dashboard on the driver’s side, near the brake pedal.
2. Remove the fusebox cover by pulling it straight out.
3. The fuse diagram is printed on the inside of the cover.

Fusebox Location in Older Jeep Wrangler Models (TJ, YJ, CJ)

In older Jeep Wrangler models, the fusebox is typically located under the dashboard on the driver’s side. However, the exact location may vary depending on the year and model of your Wrangler. Consult your vehicle’s owner manual for specific information on your fusebox location.

Fuse Types and Sizes

Jeep Wranglers use a variety of fuse types and sizes. The most common types are:

Always replace blown fuses with the same type and amperage to avoid electrical issues and potential fire hazards.

Troubleshooting Electrical Problems

If you’re experiencing electrical problems in your Jeep Wrangler, the fusebox is an excellent place to start your troubleshooting. Here are a few common issues and how to address them:

Blown Fuses

If an electrical component stops working, check the corresponding fuse in the fusebox. A blown fuse will have a broken wire or appear discolored. Replace the fuse with one of the same amperage.

Loose Fuses

Sometimes fuses can come loose, causing intermittent electrical problems. Check each fuse to ensure it is fully seated in its slot. A loose fuse can be just as problematic as a blown one.

Corrosion

Inspect the fusebox for signs of corrosion, especially if your Wrangler has been exposed to water or humid conditions. Corrosion can prevent proper electrical contact and cause fuses to blow repeatedly. Clean any corrosion with a wire brush and apply dielectric grease to help prevent future build-up.

Upgrading Your Jeep’s Electrical System

If you find yourself frequently blowing fuses or needing to install multiple high-draw accessories, it may be time to upgrade your Jeep’s electrical system. Some options include:

• Installing a higher output alternator
• Adding a second battery
• Upgrading to a larger gauge wiring
• Installing a power distribution block

Before making any significant upgrades, consult with a professional or do thorough research to ensure compatibility with your specific Jeep Wrangler model.

Conclusion

Knowing the location of your Jeep Wrangler’s fusebox is an essential part of vehicle ownership. Whether you’re troubleshooting an electrical issue or installing new accessories, being able to access and work with the fusebox is a valuable skill. By following the tips and information provided in this guide, you’ll be well-equipped to handle most electrical tasks on your Wrangler. Remember to always use the proper fuse types and sizes, and consider upgrading your electrical system if you find yourself pushing the limits of your Jeep’s stock setup.